Pump application:             Here we offer the Rovatti range of bare shaft, electric drive and tractor or PTO drive vertical Turbine pumps.    This range of turbine pumps are available with a cast iron casings, diffusers and impellers.   Some models also available with brass/ bronze impellers upon request.    These vertical turbine pumps are both powerful and efficient and constructed from durable materials.  These quality pumps are built to the highest standards giving the user many years of trouble free service.  The tractor or PTO drive pumps have a heavy duty gearbox to reduce the pump speed to approximately 540rm.   Also available with electric and engine drive heads.    Fantastic pumps to water in areas where medium to high heads are required for medium to high flows.   Suitable for agricultural, fire fighting, water transfer and municipal water supply uses.   Ideal for pumping low viscosity, clean non flammable and non explosive fluids.                            Performance data:             Performance curves are based on a kinematic viscosity value of 1mm2/s and a density of 1000 Kg/m3 at 20ºC.                            - Flow rates up to 1200m3/h.               - Heads up to 310m.               - Curve tolerance in conformity with ISO9906, appendix A               - Maximum fluid temperature: +60ºC.                           - Minimum fluid temperature: -15ºC.               - Maximum ambient temperature: +40ºC.                                - Maximum operating pressure: 12 to 32 bar (depending on pump model).          Installation:             It is recommended that these pumps be installed in a vertical position on a sturdy base frame - base frames can also be provided by Finsbury Pump Systems.

Pump application:             Here we offer the Rovatti Europa range of 50hz electric drive multistage pumps.    This full range of  multistage centrifugal pumps are available in a cast iron casings, diffusers and impellers.   Optional material builds for diffuser and impellers are available upon request.   These horizontal and vertical multistage pumps are both powerful and efficient and constructed from durable materials.  These quality pumps are built to the highest standards giving the user many years of trouble free service.   Fantastic pumps to deliver water in areas where medium to high heads are required for small to medium flows.   Suitable for domestic, commercial and industrial use.   Also ideal for pumping low viscosity, clean non flammable and non explosive fluids.                                  Performance data:             Performance curves are based on a kinematic viscosity value of 1mm2/s and a density of 1000 Kg/m3 at 20ºC.                            - Flow rates up to 300m3/h.               - Heads up to 265m.               - Curve tolerance in conformity with ISO9906, appendix A               - Maximum fluid temperature: +90ºC.                           - Minimum fluid temperature: -15ºC.               - Maximum ambient temperature: +40ºC.               - Motor protection: IP55.               - Motor insulation: Insulation class F.               - Rotational speed: 2900rpm.               - Maximum operating pressure: 27bar.      - Maximum inlet pressure: 6bar.         Installation:             It is recommended that these pumps be installed in a level position in a dry well ventilated location.   Caution: These pumps are not self priming and require a flooded suction or a priming system including a foot valve. The operation of the pump must be restricted to the thickened section on each of the performance curves.                                       

Pump application:             Here we offer the Rovatti range of bare shaft multistage pumps.    This full range of  multistage centrifugal pumps are available with a cast iron casings, diffusers and impellers.   Optional material builds for wear rings and impellers are available upon request.   These horizontal multistage pumps are both powerful and efficient and constructed from durable materials.  These quality pumps are built to the highest standards giving the user many years of trouble free service.   Fantastic pumps to deliver water in areas where medium to high heads are required for small to medium flows.   Suitable for domestic, commercial and industrial use.   Also ideal for pumping low viscosity, clean non flammable and non explosive fluids.                                  Performance data:             Performance curves are based on a kinematic viscosity value of 1mm2/s and a density of 1000 Kg/m3 at 20ºC.                            - Flow rates up to 300m3/h.               - Heads up to 200m.               - Curve tolerance in conformity with ISO9906, appendix A               - Maximum fluid temperature: +90ºC.                           - Minimum fluid temperature: -15ºC.               - Maximum ambient temperature: +40ºC.                          - Rotational speed: up to 2900rpm.               - Maximum operating pressure: 18 to 20 bar (depending on pump model).      - Maximum inlet pressure: 4 to 6bar (depending on pump model).         Installation:             It is recommended that these pumps be installed in a level position in a dry well ventilated location.   Caution: These pumps are not self priming and require a flooded suction or a priming system including a foot valve. The operation of the pump must be restricted to the thickened section on each of the performance curves.                                       

Pump application:             Here we offer the Rovatti range of large engine drive multistage pumps.    This full range of  multistage centrifugal pumps are available with a cast iron casings, diffusers and impellers.   Limited optional material builds for impellers are available upon request.   These horizontal multistage pumps are both powerful and efficient and constructed from durable materials.  These quality pumps are built to the highest standards giving the user many years of trouble free service.  These pumps are close coupled to the engine via an SAE standard pump flange and flywheel connection.   Fantastic pumps to deliver water in areas where medium to high heads are required for medium to high flows.   Suitable for domestic, commercial and industrial use.   Also ideal for pumping low viscosity, clean non flammable and non explosive fluids.                                  Performance data:             Performance curves are based on a kinematic viscosity value of 1mm2/s and a density of 1000 Kg/m3 at 20ºC.                            - Flow rates up to 1020m3/h.               - Heads up to 220m.               - Curve tolerance in conformity with ISO9906, appendix A               - Maximum fluid temperature: +90ºC.                           - Minimum fluid temperature: -15ºC.               - Maximum ambient temperature: +40ºC.                          - Rotational speed: up to 2600rpm.               - Maximum operating pressure: 10 to 22 bar (depending on pump model).      - Maximum inlet pressure: 4 to 6bar (depending on pump model).         Installation:             It is recommended that these pumps be installed in a level position in a dry well ventilated location.   Caution: These pumps are not self priming and require a flooded suction or a priming system including a foot valve. The operation of the pump must be restricted to the thickened section on each of the performance curves.                                       

Pump application:             Here we offer the Rovatti range of bare shaft and tractor or PTO drive Slurry pumps.    This range of Slurry pumps are available with a cast iron casings, diffusers and impellers.    These horizontal slurry pumps are both powerful and efficient and constructed from durable materials.  These quality pumps are built to the highest standards giving the user many years of trouble free service.  The tractor or PTO drive pumps have a heavy duty gearbox to reduce the pump speed to approximately 540rm.   Available with a range of optional attachments such as rotating inlet cutters and check valves to process and pump slurries with a high fibre content.    Fantastic pumps to move slurries in areas where low to medium to heads are required for low to medium flows.   Suitable for agricultural use.   Also ideal for pumping low viscosity, clean non flammable and non explosive fluids.    All pumps can be supplied with a 3 point linkage to fit directly behind the tractor.                              Performance data:             Performance curves are based on a kinematic viscosity value of 1mm2/s and a density of 1000 Kg/m3 at 20ºC.                            - Flow rates up to 240m3/h.               - Heads up to 130m.               - Curve tolerance in conformity with ISO9906, appendix A               - Maximum fluid temperature: +60ºC.                           - Minimum fluid temperature: -15ºC.               - Maximum ambient temperature: +40ºC.                          - Rotational speed: up to 3600rpm for the pump.                                  - Rotational speed:   around the 540rpm for the PTO driver         - Maximum operating pressure: to 15 bar (depending on pump model).      - Maximum inlet pressure: 4 to 6bar (depending on pump model).         Installation:             It is recommended that these pumps be installed in a level position in a dry well ventilated location.   Caution: These pumps are not self priming and require a flooded suction or a priming system including a foot valve. The operation of the pump must be restricted to the thickened section on each of the performance curves.