Gear pump outfits

A range of bronze and cast iron gear pump outfits.

Showing 4 products

Bronze gear pump outfits

Pump application:                    These positive displacement low inertia pumps are excellent at pumping fluids at medium to high pressures.   These pumps can be used to pump water and a large range of other non abrasive fluids including oils and molasses.  Very useful for pressure boosting, liquid transfer, factory process pumping and lubrication duties.                                                           Performance data:                    Performance curves are based on a kinematic viscosity value of 1mm2/s and a density of 1000 Kg/m3 at 20ºC.                                          - Flow rates up to 4m3/h.                      - Heads up to 140m.                      - Fluids must be clean and free from suspended abrasive particles.    - Maximum fluid temperature: +60ºC.                      - Maximum ambient temperature: +60ºC.                      - Maximum allowable pressure in casing: 15 Bar.                      - Rotational speed:  700rpm recommended maximum.                      - Comes in three pump different sizes with 3 different configurations.                     B Series - standard unit                    - Castings and gears made from L.G.2 bronze.                   - Plain bronze bearings.                   - Graphite gland packing.                   - 316 Stainless steel shafts.                   - Stainless steel cap screws.                   - Available in 3 sizes 15mm, 20mm, 25mm and a variety of electric motor or petrol engine combinations.                                                      B/RV Series - as per standard unit plus          - Full inbuilt bypass valve - interchangeable for either direction                - Bypass valve has stainless steel seat and tension spring.            - Bypass valve has a Viton O ring.         - Available in 3 sizes 15mm, 20mm, 25mm and a variety of electric motor or petrol engine combinations.                    BB Series - as per standard unit plus        - Complete with a Viton carbon - ceramic mechanical seal.       - Ball race on the drive end of drive shaft and a replaceable glacier bearing on the opposite end.       - Replaceable glacier bearings on idler shaft.       - Available in 3 sizes 15mm, 20mm, 25mm and a variety of electric motor or petrol engine combinations.               Installation:                    Securely bolt the pump unit in location. The gear pump can be installed in any orientation except for engine driven units which must be installed in a horizontal position.    However always ensure that the pump is running in the right direction.  Gear pumps can run in either direction by operating the power unit in reverse or alternatively by changing the delivery and suction pipes to opposite sides of the pump.  If closed heads are to be encountered than a pressure relief or bypass valve must be installed and set to the required pressure.   If full bypass is required ensure that the vee belts are correctly aligned with the correct tension.    Always prime the pump with the fluid to be pumped and start with a fully open discharge before throttling to pressure requirements.       Caution: Pumps will self lubricate using the pumped fluid however avoid running the  pump dry as this will create rapid wear.                                         

Drum gear pump outfits

Pump application:                    These positive displacement low inertia pumps are excellent at pumping fluids at low to medium pressures.   These pumps are especially constructed for pumping molasses from 44 gallon / 205 litre drums.    These molasses drum pumps are only available with the 13mm cast iron gear pump driven by either an 1.5hp electric motor or a 4hp Honda engine.   Other larger molasses pumps are available but are not designed for use with 44 Gallon / 205 litre drums                                                         Performance data:                      - Flow rates up to 10L/min maximum (depending on viscocity / temperature of molasses pumped).                     molasses pumped).                      - Heads up to 30m  (depending on viscocity / temperature of molasses pumped).                      - Fluids must be clean and free from suspended abrasive particles.  - Maximum fluid temperature: +60ºC.                      - Maximum ambient temperature: +60ºC.                      - Maximum allowable pressure in casing: 6 Bar.                      - Rotational speed: Nominal 200rpm for molasses.                      - Lubrication:  Blind plain bearings are self lubrication with the pumped liquid, the stuffing box has a gland packing to serve as a grease lubricated bearing.                      - Driver is either single phase 1.5kw electric motor or with a 4hp Honda engine.                      - All units come complete with anti vibration mounts which will sit on the drum.                      - All units come complete with 1 1/2" poly suction pipework and camlock fittings.                                                        Installation:                    Place the pump on the 44 gallon / 205 litre drum as shown.     Connect the pump to the poly pipe supplied with the kit.   The unit comes complete with a 1 1/2" poly suction pipe fitted with camlock fittings for ease of installation.    Connect the delivery pipework.     Each pumpset is fitted complete with Teflon gland packing suitable for pumpimg molasses.     The gear pump  must be rinsed out after use with hot water to prevent the pump from seizing up the next time it is used.            For delivery pipework it is recommended to use 2" pipework or larger.                                                                                                                                                                                                                          Caution: Pumps will self lubricate using the pumped fluid however avoid running the  pump dry as this will create rapid wear.                                            

Molasses gear pump outfit

Pump application:                    These positive displacement low inertia pumps are excellent at pumping fluids at low to medium pressures.   These pumps are especially constructed for pumping molasses.                                         Performance data:                      - Flow rates up to 7m³/h.                      - Heads up to 30m.                      - Fluids must be clean and free from suspended abrasive particles.   - Maximum fluid temperature: +60ºC.                      - Maximum ambient temperature: +60ºC.                      - Maximum allowable pressure in casing: 6 Bar.                      - Rotational speed: Nominal 200rpm for molasses.                      - Lubrication:  Blind plain bearings are self lubrication with the pumped liquid.       - Pumps can be run in reverse to change the direction of the pumped fluid.                          Installation:                    Securely bolt the pump unit in location.   The gear pump can be installed in any orientation except for engine driven units which must be installed in a horizontal position.    However always ensure that the pump is running in the right direction.  Gear pumps can run in either direction by operating the power unit in reverse or alternatively by changing the delivery and suction pipes to opposite sides of the pump.  If closed heads are to be encountered than a pressure relief or bypass valve must be installed and set to the required pressure.   If full bypass is required ensure that vee belts are correctly aligned with the correct tension.    Always prime the pump with the fluid to be pumped and start with a fully open discharge before throttling to pressure requirements.    Please note when the gear pump be used for pumping molasses, then it is strongly recommended that the inlet and discharge pipework be sized to a minimum of 3 times the diameter of the inlet and outlet ports and for the graphite gland packing to be replaced with a Teflon gland packing.     The gear pump must be rinsed out after use with hot water to prevent the pump from seizing up the next time it is used.                                                                                                                                                                                                                                   Caution: Pumps will self lubricate using the pumped fluid however avoid running the  pump dry as this will create rapid wear.                                            

Positive displacement pumps

Pump application: These positive displacement low inertia pumps are excellent at pumping fluids at low to medium pressures. These pumps can be used to pump water and a large range of other non abrasive fluids including oils. Very useful for pressure boosting, liquid transfer, factory process pumping and lubrication duties.   Applications include -         Tallow’s -         Transformers oils -         Heating oils -         Printers ink -         Bitumen emulsions -         Molasses-see Tech Data sheet POS-9 for details -         Jelly products -         Fertilizer -         Diesoline -         Kerosene -         Lubricating liquids   Performance Performance curves are based on a kinematic viscosity of 1mm²/s and a density of 1000Kg/m³ at 20ºC. -         Flow rates up to 27 m³/h -         Heads up to 30m -         Fluids must be clean and free from suspended abrasive particles -         Maximum fluid temperature: +60ºC. -         Maximum ambient temperature: +60ºC. -         Rotational speed: Nominal 400rpm with a 600rpm recommended maximum. For liquids with high viscosity, i.e. molasses the recommended speed is 200rpm – see Tech Data sheet POS-9 for special build molasses gear pump outfits -         Comes in six pump different sizes with 12 electric motor and 20 engine combinations. -         Lubrication: Blind plain bearings are self lubrication with the pumped liquid; the stuffing box has a gland packing to serve as grease lubricated bearing. -         Pumps can be run in reverse to change the direction of the pumped fluid.   Installation: Securely bolt pump unit in location. The gear pump can be installed in any orientation except for engine driven units which must be installed in a horizontal position. However always ensure that pump is running in the right direction. Gear pumps can run in either direction by operating the power unit in reverse or alternatively by changing the delivery and suction pipes to opposite sides of the pump. If closed heads are to be encountered than a pressure relief or bypass valve must be installed and set to the required pressure. If full bypass is required ensure that vee belts are correctly aligned with the correct tension. Always prime the pump with the fluid to be pumped and start with a fully open discharge before throttling to pressure requirements. Caution: Pumps will self-lubricate using the pumped fluid however avoid running the pump dry as this will create rapid wear.  

Showing 1–4 of 4 results

Top